24 July 2021 Mould Steel Bar
YG8 Mould Steel Bar
YG8 is tungsten-cobalt stamping die mould steel. With good abrasion resistance, strength and impact toughness are better than YG6. Drawing dies under high stress conditions, suitable for drawing steel with a diameter of <50mm, non-ferrous metal wires and their alloy wires or bars, and also used for stamping dies and rivet top forging dies with small size and low working load . YG8 advanced molding material. Without heat treatment, the inner and outer hardness is uniform.
Chemical Composition:
C(%) | Si(%) | Mn(%) | P(%) | S(%) | W(%) | Co(%) |
---|---|---|---|---|---|---|
0.38~0.43 | 0.15~0.30 | 0.60~0.80 | ≤0.035 | ≤0.040 | 8.00~11.00 | 1.65 ~ 2.00 |
Mechanical Propoerties:
Yield Strength Rp0.2(MPa) | Tensile Strength Rm(MPa) | Impact Energy AKV(J) | Elongation at Fracture A(%) | Reduction in Cross Section on Fracture Z(%) | Impact toughness value αkv (J/cm2) | Hardness(Brinell) |
---|---|---|---|---|---|---|
≥ 862(85) | ≥ 1282(100) | ≥ 78 | ≥ 12 | ≥ 55 | ≥ 98 | ≤ 363 |
Grade | Hardness | Density | Bendingstrength | Recommended Applichaton |
---|---|---|---|---|
YG6X | 91-93 | 14.8-15 | ≥1600 | Suitable for little stress coditions,produce for small diameter steel wire,non-ferrous metal wire or rod |
YG6 | 90.5-92 | 14.8-15 | ≥2000 | Suitable for large stress coditions,produce for medium diameter of steel wirec wire or rod |
YG8 | 89.5-91 | 14.6-14.8 | ≥2100 | Suitable for steel,non-ferrous metal and alloy rod tube ,and is suitable for manufactuting machinery parts,tools materials and wear parts |
YG8C | 89-90.5 | 14.6-14.8 | ≥2200 | Coarse grain size carbide,suitbale for drilling me dium hard or hardstratum with fless than 14th and the coal bed containing hard rock;Coal cutter Bits ;oil Field bits ,and hammer dwill bits |
YG9 | 87.5-89 | 14.3-14.5 | ≥2200 | With good good resistance,impact resistance and good shock resistance,suitable for carbide dril lpills. |
YG9C | 87.2-88.6 | 14.4-14.6 | ≥2300 | Coarse grain,with good wear resistance,suitable for drilling hard rock |
YG10 | 87-88.5 | 14.3-14.6 | ≥2300 | With good good resistance,excellent impact resistance and flat-tio-serrated compacts |
YG11 | 89-90.2 | 14.2-14.5 | ≥2300 | With good abrasion resistance,suitable for producing nail mating moulds,nails specially for cement industry |
YG11C | 86.5-88 | 14.2-14.5 | ≥2400 | Coarse grain,With good wear resistance,suitable for drilling hardrock |
YG12 | 86.5-88 | 14.1-14.4 | ≥2400 | With good toughness,suitable for making steel pipe,steel,non-ferrousmetal and alloy rods,bars,tubes |
YG15 | 87-88.5 | 13.9-14.2 | ≥2400 | Low wear resistance ,high bending strength and impact toughness.Suitable for cemented carbide dies,stamp dies and mould cores ,etc. |
YG15C | 85-86.5 | 13.9-14.2 | ≥2450 | With very good impact and shock resistance,suitable for tungstencarbide dies and mould cores ,etc. |
YG20 | 83-85 | 13.4-13.6 | ≥2700 | Suitanble for wear parts,plates andmechanical parts. |
YG20C | 82.5-84.5 | 13.4-13.6 | ≥2700 | Suitable for cold heading moulds,cold punching moulds and cold rolls for standard parts and tools in various industries. |
YN6 | 90.5-92.5 | 14.8-15.1 | ≥1700 | With good corrosinon resistant,excellent wear resistance,suitable for mechanical seal parts. |
YN7 | 90-92 | 14.7-14.9 | ≥1800 | With good corrosinon resistant,excellent wear resistance,suitable for mechanical seal parts. |
YN10 | 86-88 | 14.3-14.6 | ≥2000 | With good corrosinon resistant,suitable wear resistance |